Wednesday, August 15, 2012

Fuse Panel Update

As pointed out by Izaak on the Alazzurra Yahoo Group there is a much simpler solution.

Universal 4-way ATC fuse block with 4 separate circuits.

This is a "plug and play" with no re-wiring required. Since I won't be building a new wiring harness for the Alazzurra (yet) I'll go with one of these too.

Sunday, August 12, 2012

Replacement Fuse Panel


The stock fuse panel uses some archaic ceramic fuses. They are notorious for not making a great connection and the ease at which you can remove them bears this out. On the panel the far left fuse is the main power.


The main power starts at the alternator, goes to the voltage regulator, to starter solenoid, then to the battery. From the battery it comes to this fuse then to the general relay. From the general relay it changes to the brown wire you see at the top of the fuse panel. This is your switched power.


This is a simple fuse panel with a ground block. I may switch this out for a 4 fuse panel without the ground block as the Alazzurra grounds to the frame. For a custom harness I'd bring as many grounds as I could to the ground block.

I made a pigtail with a round connector at one end to fit onto the power block and a spade connector on the other. It will fit in the stock brown wire connector. Having the extra connection isn't idea but it retains the stock wiring connector and I don't cut into the harness.

Then I'll move the three wires to the new fuse block. The first one is the turn signals and brake lights. The next one is horn and the last one goes to the handlebar switch.

I'll also add a separate 25 amp inline fuse to the main power. The other fuses will be 8-10 amps.

Tuesday, July 31, 2012

Lower Fairing


A quick note. I did get the lower fairing pieces finally. I need to figure out how they mount. I think I have the lower brackets (I think they mount to the exhaust).

Of course I need to fix all the oil leaks before attaching the fairing.

Sunday, July 29, 2012

Seat Release

So I was going to tune the carbs but the left petcock decided to leak badly. Gas dripping on the exhaust is not a most excellent idea so that task is being postponed until new petcocks are sourced.

In the meantime I rectified the seat lock issue. The issue is the ignition key does't operated the seat release mechanism. To get the seat off I'm resorted to a spring puller hook thing as my "key". Luckily there is a nice space on top of the taillight that let's you access the area.

The proper way to fix the issue would be to take the lock to a locksmith and have them modify the lock to work with the ignition key, and some day I may do just that. But in the meantime I needed a more practical solution.


I removed the grab bars on each side and this allowed me to remove the seat cowl. There are spacers on the top of the grab rails. One leapt off the bike and rolled to the center of the nearest car. Maybe this wasn't a good idea...

In the meantime I looped a zip tie around the seat release "hook". It's actually pretty secure and I don't expect it to go anywhere.


Once assembled, and I mean after an hour of fighting the spacers on the top mounts, all that you have to do is pull on the tie. Before that could happen I kept dropping the spacers into a well on top of the taillight. I lost count the number of times I had to fish them out.


Now all I have to do is fish out the zip tie and with a quick yank have the seat off. Now if the rest of my issues were so easily solved...

Thursday, July 26, 2012

Bevel Heaven - Desmo Ramblings

This was recommended by Ron on the Alazzurra Yahoo Mailing list. I think I'd probably read it before when looking for tuning info on the 860. As the carbs are very similar the info will work with both bikes.


I haven't had a chance to try this out but will very soon. I managed to borrow a vacuum sync tool that should work.

Bevel Heaven - Desmo Ramblings


Our bevel drives can be made to run extremely well with the stock dellorto carbs - especially if the carbs are in tune. If they are not adjusted correctly, your performance will be severely lacking... Here is what I do after a carb rebuild or disassembly and cleaning etc;

First off, I disassemble, clean and properly lubricate the throttle assembly and throttle cables. I also make sure that the cable doesn't bind or have any sharp bends between throttle assembly and carbs when I reinstall [smooth bends!!!].

Check your exhaust gaskets [between the heads and the exhaust pipe] to make sure they are good [did you safety wire the nuts in place??]. Also make sure the intake manifold insulators are in good condition [the rubber spacer between head and intake manifold]. You can safely check to see if the intake manifold insulators are sealing well or are leaking by warming up your bike, going outside and spraying just a bit of carb cleaner around the rubber. If they are leaking then your idle will increase for a bit. Once I have checked the insulators and exhaust gaskets AND properly maintained the throttle and cables I turn my attention to the carbs.

Assuming you rebuild and setup the carbs correctly this is what I do to adjust them correctly and easily. Print this out, go to your bike and read this over a few times while you stare at things. Once you understand the bottom line, warm up your bike and go for it.

WHAT TO DO
*Back out slide screws so they are not touching slides
*seat [turn in] the mixture screw completely [closed] then back it out 1.5 turns
*loosen throttle cables so there is at least 1/8" freeplay at the adjusters on top of carbs
*warm up bike and hook up vacuum gauges [OK] or mercury tubes [great]
*adjust slide screws so you have an even idle tickover w/even vacuum readings, don;t worry about the rpm at this point, just same vacuum readings.
*turn throttle so tickover goes to 2-2500 RPM or thereabouts and hold her steady [a friend here makes it easy]
*adjust for even vacuum at this RPM by the cable adjusters on top of carb[s] - adjustment starts by backing out whichever adjuster needs to be backed out [on whichever carb] to get constant vacuum between both carbs
*check idle vacuum again and re adjust as necessary. Adjust for proper tickover RPM now, using the slide screws only.
*adj cables so each has just a bit of freeplay, check 2500 PRM vacuum reading w/gauges again and readjust at the cable adjusters as req'd
*start playing with mixture screw for max idle [in = leaner or less gas]. I listen for sound change with my fingers over the muffler end while I turn the mixture screw on that cylinder's carb.

I go back and forth between the carbs sometimes several times making little adjustments, always listening for high tickover and feeling for a stronger exhaust pulse.

A dull BUH BUH BUH sound indicates you can make it better still. Keep adjusting until you hear and feel a louder and more authorative BAH! BAH! BAH!

WHAT IT MEANS
Adjusting the cables is an integral part of carbie sync and verse visea. Start at the top of this list, go through it then repeat a couple or 4 times as necessary...... You will get the hang of it soon enough and you will be surprised at how well your bike runs after this important step in the tune up game. You are making sure the slides are being pulled evenly causing equal vacuum through each carb from idle all the way through the range.

I also recommend that you pitch a single cable throttle - you know, the kind that has one cable going to a splitter then 2 cables one going to each carb in favour of a Tommaselli Daytona 2C throttle or the like. The DAYTONA throttle has some key adjustments - you can play with the throttle stop on it so that max pull doesn't pull the slides up against the top cap...... that will start ruining things for sure. Some of the stock throttles didn't have a stop so you would pull the slides up against the top cap and stretch the cables and wear the throttle assy, slides, etc etc.. The DAYTONA throttle also has a friction device so that you can give her partial throttle and tighten it up for a higher tickover during warmup.

Speaking of warmup..... make sure you do so. Running your bevel drive under load when cold will kill the bottom end. Blip the throttle until you feel some heat on the case on that first startup of the day then go ride taking it easy for a bit.

Sunday, July 15, 2012

Huffing and puffing


So now, in addition to the racing engine, there is a puffing sound coming from the front carb.  My next task is to take the tank off again and recheck all the carb cables. Something is not right.

Under Pressure

In yesterday's episode we have a failure of the oil pressure sending unit. Oil was pouring out of it. A little research showed that this is not uncommon.

 I'm not sure if it was too much oil that caused it to fail. I'm also not sure if this the original switch or if it was replaced at some point.

Here's the replacement part. I got it from NAPA (Part Number OP6172) for $8.12, which I'm sure it a little less than if I had to get one from a Ducati dealer. It's a little larger (it took a 22mm wrench instead of a 3/4in one). Otherwise it was pretty close in size.

With a little application of my garage hair dryer I warmed the cover and slipped it on. There are reports that the replacement sender may not last long, so we'll see.